吴忠躺衫网络科技有限公司

電子發燒友App

硬聲App

0
  • 聊天消息
  • 系統消息
  • 評論與回復
登錄后你可以
  • 下載海量資料
  • 學習在線課程
  • 觀看技術視頻
  • 寫文章/發帖/加入社區
會員中心
創作中心

完善資料讓更多小伙伴認識你,還能領取20積分哦,立即完善>

3天內不再提示
電子發燒友網>電子資料下載>類型>參考設計>具有輸入過電壓保護的CN0241高端電流傳感

具有輸入過電壓保護的CN0241高端電流傳感

2021-03-23 | pdf | 905.03KB | 次下載 | 3積分

資料介紹

This version (03 Jan 2021 22:05) was approved by Robin Getz.The Previously approved version (21 Sep 2017 01:57) is available.Diff

CN0241 High-Side Current Sensing with Input Overvoltage Protection

Overview

High-side current monitors are likely to encounter overvoltage conditions from transients or when the monitoring circuits are connected, disconnected, or powered down. This circuit uses the overvoltage protected ADA4096-2 op amp connected as a difference amplifier to monitor the high-side current. The ADA4096-2 has input overvoltage protection, without phase reversal or latch-up, for voltages of 32V higher than and lower than the supply rails.

The circuit is powered by the ADP3336 adjustable low dropout 500 mA linear regulator, which can also be used to supply power to other parts of the system, if desired. Its input voltage can range from 5.2V to 12V when set for a 5V output. To save power, the current sensing circuit can be powered down by removing power to the ADP3336; however, the power source, such as a solar panel, can still operate.

This applies voltage to the inputs of the unpowered ADA4096-2; however, no latch-up or damage occurs for input voltages up to 32V. If slower throughput rates are required, the AD7920 can also be powered down between samples. The AD7920 draws a maximum of 5 μW when powered down and 15 mW when powered up. The ADA4096-2 requires only 120 μA under operational conditions. When operating at 5V, this is only 0.6 mW. The ADP3336 draws only 1 μA in the shutdown mode.

Required Equipment

General Setup

Block Assignments

  1. Connect EVAL-CN0241-SDPZ (CN0241 Board) to the EVAL-SDP-CB1Z (SDP-B Board) via the 120-PIN Connector (SDP CONN).
  2. Connect a 6V power supply to the +6V and GND pins on the board. If available, a 6 V wall wart can be connected to the barrel connector, J5, in place of the 6V power supply.
  3. Connect the 5V/2.5 A dc supply to +VIN and GND on J1. Also connect the 2 Ω/12 W load resistor to LOAD and GND on J1.
  4. J2 is for SPI breakout.

Installing the Evaluation Software

  1. Download and extract the file CN0241 Evaluation Software and open setup.exe

    NOTE: It is recommended that you install the CN0241 Evaluation Software to the default directory path C:/Program Files (x86)/Analog Devices/CN0241/ and all National Instruments products to C:/Program Files/National Instruments/


  2. Click Next and accept license agreement.
  3. Click Next to view the installation review page
  4. Click Next to start the installation
  5. Upon completion of the installation of the CN0241 Evaluation Software, the installer for the ADI SDP Drivers will execute.

    NOTE: It is recommended that you close all other applications before clicking “Next”. This will make it possible to update relevant system files without having to reboot your computer.



  6. Click Next to set the installation location for the SDP Drivers

    It is recommended that you install the drivers to the default directory path
    C:/Program Files/Analog Devices/SDP/Drivers


  7. Click Next to install the SDP Drivers. When prompted by Windows Security, just press Install

  8. Click Finish to complete the installation

Running the System

  1. Apply power to the 6V supply (or wall wart) connected to the CN0241 Evaluation Board.
  2. Connect USB cable from PC to the USB miniconnector on the SDP-B board.
  3. Launch CN0241 Evaluation Software from the default installation location.
  4. Click “Connect” to start communication between SDP-B and CN0241 Evaluation Board
  5. Upon successful connection, select SDP connector A
  6. Set the desired number of samples.
  7. Turn the 5 V/2.5 A dc supply on when data is ready to be acquired.
  8. Adjust the voltage output accordingly to output the amount of current needed to be measured
  9. Click “Sample Data” to start acquisition of data.

Using the Evaluation Software

Main Window

  1. Connect Button - Starts the connection between the CN0241 Evaluation Board and SDP-B Controller Board.
  2. Disconnect Button - Ends the connection between the CN0241 Evaluation Board and SDP-B Controller Board.
  3. Select SDP connector - Selects which 120-pin connection of the SDP-B Board to use.
  4. Sample Size - Sets the number of samples.
  5. Sample Data Button - Starts the acquisition of measurement data.
  6. Save Data Button - Saves the acquired measurement data.
  7. Sample Data Tab
    • Shows the acquired measurement data in terms of ADC codes with respect to the samples.
    • By right-clicking within the area, more functions can be viewed. Graph palette can be hidden by deselecting it and also other items can be added such as plot legend, scale legend, etc.
  8. Histogram Tab
    • Shows the acquired measurement data in terms of Number of counts with respect to the ADC codes
    • The same as the previous tab, by right-clicking within the area, more functions can be viewed. Other items can be added such as plot legend, scale legend, etc.
  9. Configure Tab
    • AD7920 Mode - Can choose between two modes:
      • Power Down Between Conversions
      • Normal Operation
    • Read Firmware - Reads the firmware of CN0241 Evaluation Board
    • Flash LED - Flashes the LED on the SDP controller board
  10. Quit Button
    • Closes the evaluation software.

Schematic, PCB Layout, Bill of Materials

EVAL-CN0241-SDPZ Design & Integration Files

  • Schematics
  • PCB Layout
  • Bill of Materials
  • PADS project
下載該資料的人也在下載 下載該資料的人還在閱讀
更多 >

評論

查看更多

下載排行

本周

  1. 1電子電路原理第七版PDF電子教材免費下載
  2. 0.00 MB  |  1491次下載  |  免費
  3. 2單片機典型實例介紹
  4. 18.19 MB  |  95次下載  |  1 積分
  5. 3S7-200PLC編程實例詳細資料
  6. 1.17 MB  |  27次下載  |  1 積分
  7. 4筆記本電腦主板的元件識別和講解說明
  8. 4.28 MB  |  18次下載  |  4 積分
  9. 5開關電源原理及各功能電路詳解
  10. 0.38 MB  |  11次下載  |  免費
  11. 6100W短波放大電路圖
  12. 0.05 MB  |  4次下載  |  3 積分
  13. 7基于單片機和 SG3525的程控開關電源設計
  14. 0.23 MB  |  4次下載  |  免費
  15. 8基于AT89C2051/4051單片機編程器的實驗
  16. 0.11 MB  |  4次下載  |  免費

本月

  1. 1OrCAD10.5下載OrCAD10.5中文版軟件
  2. 0.00 MB  |  234313次下載  |  免費
  3. 2PADS 9.0 2009最新版 -下載
  4. 0.00 MB  |  66304次下載  |  免費
  5. 3protel99下載protel99軟件下載(中文版)
  6. 0.00 MB  |  51209次下載  |  免費
  7. 4LabView 8.0 專業版下載 (3CD完整版)
  8. 0.00 MB  |  51043次下載  |  免費
  9. 5555集成電路應用800例(新編版)
  10. 0.00 MB  |  33562次下載  |  免費
  11. 6接口電路圖大全
  12. 未知  |  30320次下載  |  免費
  13. 7Multisim 10下載Multisim 10 中文版
  14. 0.00 MB  |  28588次下載  |  免費
  15. 8開關電源設計實例指南
  16. 未知  |  21539次下載  |  免費

總榜

  1. 1matlab軟件下載入口
  2. 未知  |  935053次下載  |  免費
  3. 2protel99se軟件下載(可英文版轉中文版)
  4. 78.1 MB  |  537793次下載  |  免費
  5. 3MATLAB 7.1 下載 (含軟件介紹)
  6. 未知  |  420026次下載  |  免費
  7. 4OrCAD10.5下載OrCAD10.5中文版軟件
  8. 0.00 MB  |  234313次下載  |  免費
  9. 5Altium DXP2002下載入口
  10. 未知  |  233046次下載  |  免費
  11. 6電路仿真軟件multisim 10.0免費下載
  12. 340992  |  191183次下載  |  免費
  13. 7十天學會AVR單片機與C語言視頻教程 下載
  14. 158M  |  183277次下載  |  免費
  15. 8proe5.0野火版下載(中文版免費下載)
  16. 未知  |  138039次下載  |  免費
百家乐官网打鱼秘| 百家乐官网赌机厂家| 大发888体育| 百家乐官网的出牌技巧| 安庆市| 六合彩现场开奖结果| 涂山百家乐的玩法技巧和规则| 百家乐游戏机博彩正网| 好运来百家乐官网的玩法技巧和规则 | 威尼斯人娱乐城位置| 百家乐制胜软件| 百家乐庄闲当哪个好| 百家乐官网麻将筹码币| 百家乐官网赌术大揭秘| 百家乐官网高手论坮| 大发在线扑克| 百家乐官网博彩网太阳城娱乐城| 太阳城百家乐官网群| 尊龙线上娱乐| bet365会员注册| 百家乐赌博游戏| 互博百家乐现金网| 大西洋百家乐官网的玩法技巧和规则| 百家乐官网画面| 百家乐官网套路| 蓝盾百家乐官网娱乐场开户注册| 磴口县| 鄂托克旗| 百家乐官网游戏机说明书| 新澳博天上人间娱乐| 正蓝旗| 蚌埠市| 百家乐官网de概率| 民丰县| 玉田县| 百家乐官网开户百家乐官网技巧| 门赌场百家乐官网的规则| 百家乐官网白菜价| 赌博百家乐官网下载| 网络百家乐官网输了很多钱| 百家乐官网真钱在线|