吴忠躺衫网络科技有限公司

電子發燒友App

硬聲App

0
  • 聊天消息
  • 系統消息
  • 評論與回復
登錄后你可以
  • 下載海量資料
  • 學習在線課程
  • 觀看技術視頻
  • 寫文章/發帖/加入社區
會員中心
創作中心

完善資料讓更多小伙伴認識你,還能領取20積分哦,立即完善>

3天內不再提示
電子發燒友網>電子資料下載>類型>參考設計>CN0418用戶指南

CN0418用戶指南

2021-03-23 | pdf | 2.4MB | 次下載 | 3積分

資料介紹

This version (07 Jan 2021 09:06) was approved by Ioana Chelaru.The Previously approved version (03 Jan 2021 21:55) is available.Diff

EVAL-CN0418-ARDZ Shield Overview

The circuit shown in Figure 1 provides a complete, fully isolated and highly flexible, 4-channel analog output system suitable for programmable logic controllers (PLCs) and distributed control system (DCS) applications that require ±5 V, ±10 V voltage and 4 mA to 20 mA current output with HART-compatibility. All outputs are protected from transients and are suitable for the most harsh industrial environments.

The HART compatibility of this module provides a complete field communications solution that is simple to use, low cost, and extremely reliable.

The circuit is powered from a standard 24 V bus supply, with on-board filtering and protection circuitry. Because many factories and industrial environments power their PLC/DCS from a 24 V standard bus line, this module is easy to integrate into any existing system. This module can also be powered from other standard supplies, starting from 12 VDC to 28 VDC

This user guide will discuss how to use the EVAL-EVAL-ADICUP3029 and evaluation software to configure and collect data from the EVAL-CN0418-ARDZ Evaluation Board (CN-0418 Board).

EVAL-CN0418-ARDZ attached to EVAL-ADICUP3029

Simplified functional block diagram


General Setup

Equipment

  • PC with a USB port and Windows 7 (32-bit) or higher
  • Serial Terminal Software (Putty/TeraTerm or similar)
  • DC Power Supply (+12 V to +24 V / 1 A) or equivalent bench supply (optional)
  • Precision voltage and current source (for output measurement)
  • USB type A to micro USB type A cable
  • CN0418 Evaluation Software

  • The EVAL-CN0418-ARDZ (CN-0418 Board) connects to the EVAL-ADICUP3029 (ADICUP3029 Board)
  • The EVAL-ADICUP3029 (ADICUP3029 Board) connects to the PC via the USB cable.
  • Terminal block P1 is the power supply input (input:+24V DC)
  • Terminal blocks P6 provide the quad channel voltage output (-10V to +10V), and Current output (0mA to 24mA) and standard 4 mA to 20 mA HART compatible current inputs.

Power Supply Considerations and Configuration (P1)

Terminal block P17 is the power supply input (input range:+12V to +36V DC). The EARTH terminal can be connected to an external earth connection, to the GND terminal or left floating if an external earth connection is not used. The Green power LED should lit up when connected to a power supply.

Default Shunt Jumper (P9 and P10) and DIP Switches (S3 and S4) Configuration

The default jumper position for P9 and P10 are shorted at position 1 and 2 while the two DIP switches S3 and S4 should be in ON state switch position.

P9 jumper connections for HART enable (EN) control P10 jumper connections for Chip select (SYNC) control

Single board

If only a single board is used, then connect jumpers P9 and P10 as shown in the table below.

Position Description Mode Position Description Mode
pin 1 & pin 2 skip decoder single pin 1 & pin 2 skip decoder single

Multi board

If more than one board is stacked (up to 4), then each board must be set to a different DAC and HART select address. Connect jumpers P9 and P10 as shown in the table below, and ensure that the software is configured accordingly. On a given board, set the DAC and HART address to the same position. If necessary, the software can be changed to address differently the DAC and HART on a given board.

Position Description Mode Position Description Mode
pin 4 & pin 6 AIN2:AIN3 = 00 multiple pin 4 & pin 6 AIN0:AIN1 = 00 multiple
pin 3 & pin 5 AIN2:AIN3 = 01 multiple pin 3 & pin 5 AIN0:AIN1 = 01 multiple
pin 7 & pin 5 AIN2:AIN3 = 10 multiple pin 7 & pin 5 AIN0:AIN1 = 10 multiple
pin 8 & pin 6 AIN2:AIN3 = 11 multiple pin 8 & pin 6 AIN0:AIN1 = 11 multiple

Default EEPROM Address configuration of Solder Jumper position JP2, JP3 and JP4

EEPROM default address configuration of the board is “000” you can configure the EEPROM I2C address from 000 to 111.

Default EEPROM WP ( Write Protect) mode configuration of Solder Jumper JP1

EEPROM WP pin can be configured as single or multi board operation. The default connection of WP pin is shorted to GND.

JP1 soldering position
Position Description
pin 2 & pin 3 enable write protection (WP) (single board operation by default)
pin 2 & pin 1 control write protection (WP) (multi board operation)

16 bit Voltage and Current Analog Output Connection (P6)

Peripheral Connectors

All connector pinouts for the EVAL-CN0418-ARDZ are described in the table below.

Connector Pin No. Pin Name ADuCM3029 Pin Function CN0418 Pin Function
Arduino DIO High 1 SCL I2C0_SCL/GPIO04 SCL (EEPROM)
2 SDA I2C0_SDA/GPIO05 SDA (EEPROM)
3 AREF VREF+ NC
4 AGND AGND (Analog ground) DGND
5 SCLK SPI0_CLK/SPT0_BCLK/GPIO00 DAC_SCLK (AD5755-1)
6 MISO SPI0_MISO/SPT0_BD0/GPIO02 DAC_MISO_BUFF (AD5755-1)
7 MOSI SPI0_MOSI/SPT0_BFS/GPIO01 DAC_MOSI (AD5755-1)
8 CS SPI0_CS1/SYS_CLKIN/SPI1_CS3/GPIO26 DAC_SYNC(AD5755-1)
9 RDY SPI0_RDY/GPIO30 HART_MULT_A0(AD5700-1)
10 IO28 GPIO28 HART_MUL_A1(AD5700-1)
Arduino DIO Low 1 IO08 BPR0_TONE_N/GPIO08 DAC_FAULT(AD5755-1)
2 IO27 TMR1_OUT/GPIO27 AD5700_RTS (AD5700-1)
3 IO33 XINT0_WAKE3/TMR2_OUT/GPIO33 AD5700_CD_BUFF(AD5700-1)
4 IO09 BPR0_TONE_P/SPI2_CS1/GPIO09 SW_TXD (AD5700-1)
5 IO13 XINT0_WAKE2/GPIO13 HW RXD (AD5700-1)
6 IO15 XINT0_WAKE0/GPIO15 NC
7 TX UART0_TX/GPIO10 NC
8 RX UART0_RX/GPIO11 NC
Arduino Analog 1 AIN0 ADC0_VIN0/GPIO35 HART_COM_A0
2 AIN1 ADC0_VIN1/GPIO36 HART_COM_A1
3 AIN2 ADC0_VIN2/GPIO37 DAC_COM_A0
4 AIN3 ADC0_VIN3/GPIO38 DAC_COM_A1
5 AIN4 ADC0_VIN4/SPI2_CS3/GPIO39 NC
6 AIN5 ADC0_VIN5/SPI0_CS2/GPIO40 NC
Arduino Power 1 NC - not connected - NC
2 IOREF +3.3V IO_VREF (+3V3)
3 RESET SYS_HWRST_N NC
4 3.3V +3.3V NC
5 5V +5V 5V
6 GND DGND (Digital Ground) GND
7 GND DGND (Digital Ground) GND
8 Vin DC Barrel Jack Power +7V to +12V +7.5V


Advanced Setup

Up to four EVAL-CN0418-ARDZ boards can be controlled by a single Arduino or EVAL-ADICUP3029 base board by using a simple control scheme. This control scheme will control the SYNC, CD and RX signals to avoid a data conflict.


Schematic, PCB Layout, Bill of Materials

EVAL-CN0418-ARDZ Design & Integration Files

  • Schematics
  • PCB Layout
  • Bill of Materials
  • Allegro Project

Software

End of Document

評論

查看更多

下載排行

本周

  1. 1電子電路原理第七版PDF電子教材免費下載
  2. 0.00 MB  |  1491次下載  |  免費
  3. 2單片機典型實例介紹
  4. 18.19 MB  |  95次下載  |  1 積分
  5. 3S7-200PLC編程實例詳細資料
  6. 1.17 MB  |  27次下載  |  1 積分
  7. 4筆記本電腦主板的元件識別和講解說明
  8. 4.28 MB  |  18次下載  |  4 積分
  9. 5開關電源原理及各功能電路詳解
  10. 0.38 MB  |  11次下載  |  免費
  11. 6100W短波放大電路圖
  12. 0.05 MB  |  4次下載  |  3 積分
  13. 7基于單片機和 SG3525的程控開關電源設計
  14. 0.23 MB  |  4次下載  |  免費
  15. 8基于AT89C2051/4051單片機編程器的實驗
  16. 0.11 MB  |  4次下載  |  免費

本月

  1. 1OrCAD10.5下載OrCAD10.5中文版軟件
  2. 0.00 MB  |  234313次下載  |  免費
  3. 2PADS 9.0 2009最新版 -下載
  4. 0.00 MB  |  66304次下載  |  免費
  5. 3protel99下載protel99軟件下載(中文版)
  6. 0.00 MB  |  51209次下載  |  免費
  7. 4LabView 8.0 專業版下載 (3CD完整版)
  8. 0.00 MB  |  51043次下載  |  免費
  9. 5555集成電路應用800例(新編版)
  10. 0.00 MB  |  33562次下載  |  免費
  11. 6接口電路圖大全
  12. 未知  |  30320次下載  |  免費
  13. 7Multisim 10下載Multisim 10 中文版
  14. 0.00 MB  |  28588次下載  |  免費
  15. 8開關電源設計實例指南
  16. 未知  |  21539次下載  |  免費

總榜

  1. 1matlab軟件下載入口
  2. 未知  |  935053次下載  |  免費
  3. 2protel99se軟件下載(可英文版轉中文版)
  4. 78.1 MB  |  537793次下載  |  免費
  5. 3MATLAB 7.1 下載 (含軟件介紹)
  6. 未知  |  420026次下載  |  免費
  7. 4OrCAD10.5下載OrCAD10.5中文版軟件
  8. 0.00 MB  |  234313次下載  |  免費
  9. 5Altium DXP2002下載入口
  10. 未知  |  233046次下載  |  免費
  11. 6電路仿真軟件multisim 10.0免費下載
  12. 340992  |  191183次下載  |  免費
  13. 7十天學會AVR單片機與C語言視頻教程 下載
  14. 158M  |  183277次下載  |  免費
  15. 8proe5.0野火版下載(中文版免費下載)
  16. 未知  |  138039次下載  |  免費
威尼斯人娱乐场 五星| 网络百家乐棋牌| 百家乐有试玩的吗| 百家乐官网网投打法| 百家乐平台租用| 伊通| 百家乐技术辅助软件| 百家乐官网只打闲打法| 亲朋棋牌完整版下载| 澳门百家乐哪家信誉最好| 百家乐官网的注码技巧| bet365 体育在线uo| 诚信百家乐在线平台| 百家乐官网三号的赢法| 百家乐平注法到6568| 娱乐城百家乐官网技巧| 58娱乐城开户| 精通百家乐的玩法技巧和规则| 宝马百家乐官网的玩法技巧和规则 | 百家乐官网斗地主炸金花| 蒙特卡罗国际| 百家乐娱乐网站| 百家乐官网制胜法| 大发888 casino exe| 百家乐平台开户哪里优惠多| 百家乐官网技巧经| 百家乐官网的玩法和技巧| 盈乐博| 青海省| 百家乐官网出千原理| 德州扑克读牌| 澳门百家乐限红规则| 澳门百家乐介绍| 澳门百家乐娱乐城送彩金| 24山来水吉凶| 百家乐官网9人桌布| 百家乐官网庄家胜率| 足球竞猜推荐| 元游棋牌游戏大厅| bet365后备网址| 炸金花棋牌游戏|